Proving the Safety of CROHMIQ

Proving the safety of CROHMIQ® FIBC

TEXENE is the premier and recognized world leader in ungrounded static protective fabric for Type D (Antistatic) FIBC. As part of its on-going commitment to safety and product development, the company maintains a state of the art, full-scale FIBC safety performance testing facility in Miami Lakes, Florida, USA. This 7400 cu.ft environmentally controlled facility has been designed to meet the requirements of the international test standard, IEC 61340-4-4 Ed 2.0 and incorporates two laboratories, each with a full FIBC test rig. The laboratories are directed by Dr. Paul Holdstock, whom possesses a PhD in electrostaticscs.

Inside the test facility, full-scale FIBC are filled and emptied under electrostatic charging conditions that simulate industrial environments. Testing parameters include FIBC grounded (for static protective Type D bulk bags) or ungrounded (for Type C bulk bags), temperature, relative humidity and electrostatic charging rate. Performance measurements of the FIBC include charge transfer, surface potential, and incendivity testing using a gas probe with specific mixtures for a range of minimum ignition energies. In addition to bulk bag testing, the electrostatics laboratory is utilized to measure electrostatic properties, such as surface resistivity, breakdown voltage for fabrics, linear resistivity and resistance to groundable points.

To ensure the continued safety of ungrounded and groundable Type D FIBC manufactured from CROHMIQ ® fabric, TEXENE regularly conducts tests in its safety performance test laboratories located in Miami Lakes, FL. The most important test that proves the safety of FIBC for use in flammable or explosive atmospheres is the incendivity, or ignition test. The principle is to fill the bulk bag under test with charged pellets and determine if there are any electrostatic discharges from the surface of the bulk bag with sufficient energy to ignite an approaching gas probe. The test parameters are selected to provide the severest challenge to antistatic FIBC so as to ensure they are able to perform safely under worst case conditions. The critical test parameters and the significance of each are described below.

Test Parameters & Their Significance




The electrostatic properties of polymeric materials depend to a greater or lesser extent on the amount of moisture they are able to absorb from the atmosphere. There is too little moisture available at low relative humidity and so static charge tends to accumulate more readily and dissipate more slowly.

Some materials absorb a lot of moisture and at high relative humidity their resistance can be so low that spark discharges may occur if the materials are isolated from ground.

To ensure that CROHMIQ® Type D bulk bags are able to maintain safe charge dissipation without becoming too conductive, it is necessary to test at both low and high relative humidity.

Charging current

The rate at which charge flows into and out of a bulk bag depends on the speed of filling and emptying and the chargeability of the product. Charging current is the charge flow rate expressed as ampere (A), or more conveniently micro-ampere (µA).

End-user data has shown that sustained charging currents of about 3 µA are possible, with transients sometimes even higher. It is necessary to test using charging currents that replicate those found in industry.

Minimum Ignition Energy


MIE is the smallest quantity of energy in an electrostatic discharge required to cause the ignition of a gas, vapor or powder. MIEs are normally expressed in milli-joule (mJ). The severest incendivity test is to use a gas mixture with the lowest practically relevant MIE.

Methanol vapor has the lowest MIE of any gas or solvent that is likely to be present when bulk bags are emptied. The MIE for methanol is 0.14 mJ. Click here for MIE of other common substances.

Gas Composition

The gas selected for incendivity testing is mixed with air to achieve the required MIE. The ratio of gas to air must be controlled to tight tolerances in order to maintain the specified MIE throughout the test. Furthermore, the composition of the air used must also be controlled.

MIE normally changes with gas composition in a way similar to that shown below:

 FIBC ���-

Small changes in gas composition can produce a dramatic increase in MIE, making it easier to pass the test. Precise control of the gas composition is essential if the severity of the test is to be maintained.

Gas Flow Rate

The gas probe used for incendivity testing is a grounded metal electrode surrounded by a shroud that directs a flow of gas in front of the electrode, as shown below:

FIBC ���-

As gas exits the probe it is diluted by the surrounding air. It is necessary to minimize dilution because it changes the MIE of the gas. If the gas flow rate is high enough, dilution will not be significant.

Number of Repeat Tests

Ignition of a gas by electrostatic discharges is a probabilistic phenomenon. For example, a 1 mJ spark might ignite a 0.1 mJ MIE gas every time, but a 0.1 mJ spark may only ignite the same gas 1 time out of 100.

Confidence of a pass in incendivity testing (i.e. no ignitions) can only be achieved by performing a statistically significant number of gas probe approaches. Furthermore, approaches should be made at different locations on all sides of the bulk bag under test, during filling and emptying.

Parameters used for Testing CROHMIQ® FIBC

Temperature & Humidity

(23 ± 2) °C / (20 ± 5) %RH, and

(23 ± 2) °C / (60 ± 10) %RH

Charging Current

(3.0 ± 0.2) µA negative polarity


(0.14 ± 0.01) mJ

Flammable Gas



(21.0 ± 0.5)% Oxygen, balance Nitrogen

Gas Composition

(5.4 ± 0.1)% Ethylene

Gas Flow Rate

(0.21 ± 0.04) litre/s

Gas Composition Monitoring

IR Ethylene Gas Analyzer providing constant, real-time monitoring

Calibration Checks

Before each test series:

  • Mass flow rate of pellets
  • Charging current
  • Gas Analyzer checked using reference gas with composition traceable to NIST standards

Number of Repeat Tests

At least 50 on each side, top and bottom (>200 per FIBC)

Test Results



TEXENE LLC, Textile Technologies of the 21st Century
Textile Technologies of the 21st Century

TEXENE LLC is a leading manufacturer of technical textiles focused on delivering precision engineered, safety performance products worldwide.


In the early 1990's, Dr Laurence G. Britton, a highly respected process safety engineer with Union Carbide Corp. (later Dow Corp.), conducted a study of fire and explosion incidents that occurred when FIBC were ...

Following three fatal dust explosions in 2003 alone, the US Chemical Safety & Hazard Investigation Board (CSB) launched a wide ranging study of industrial dust explosions.  This first issue of our Electrostatic Safety ...

The second issue of our Electrostatic Safety Review outlines the development of conductive Type C FIBC and the later development of CROHMIQ, the world's first truly effective Type D FIBC fabric, which provides ...

The third issue in our series of Electrostatic Safety Reviews describes the rigorous testing that is demanded by national and international standards such (IEC, CENELEC, NFPA, etc.) in order to prove the safety of ...

Companies that handle combustible powders in bulk bags, or empty products from bulk bags in environments where flammable solvents may be present rely on safe antistatic FIBC to prevent fires and explosions. Proving safety ...